Circular Saw For Table Mounting: 8 Easy Ways to Build One!

Q: What blades are best for circular saw table mounting?

Any circular saw blade would work fine as a table saw. Just make sure the blade and the board are in a perfect 90-degree position. The best blade as a table saw would be a carbide-tipped saw blade as it reduces heat generation. You should avoid diamond blades are they are super sharp and risky without any safety gear.

If you have a circular saw, investing in a table saw separately would be a waste. If you are handy with your circular saw, you can use the circular saw for table mounting without attaching the saw permanently to the table.

You can make a table saw mounting from a circular saw. All you will need is a circular saw, a few boards for the table, and a drill machine. However, make sure you know about the risks before using table mounting.

For more details, I urge you to thoroughly read the full article.

Table of Contents

[show]

Circular Saw For Table Mounting

There are many ways for the circular saw for table mounting. You should opt for the method that you feel comfortable with as per your skill and experience. There are some pros and cons to all methods, but you have to choose the right one for you to mount a table with a circular saw. For your convenience, I have discussed that process that would be easy for all.

The most popular method of table mounting by the circular saw is by building a table saw sled that holds the circular saw. there would be a jig that attaches to the saw that will allow it to glide following the track, just like the table saw operates. This method ensures a precise and accurate cut. But this method will require some wood crafting skills.

Another way to mount a table saw with a circular saw is by using a miter gauge or a saw guide. This is a good setup for temporary use and can’t be built quickly. This is an easy setup that anybody can pull off. But this might not be as precise and steady as the sled.

How To Mount A Table Saw By A Circular Saw

Interestingly, you can make a table saw with the circular saw and the materials to make the table saw can be cut via the circular saw as well. All you need is a thorough guideline to make a table saw that is mounted by the circular saw. Without further ado, let’s get started.

1. Drill Four Holes In The Base Plate

The flat surface of the circular saw that adjoins the material is the base plate or the shoe. First, you need to drill a five-millimeter hole in each corner of the circular saw. Make sure the holes are aligned and straight as those will be the new fixing point to the board.

Drill another hole in the middle on the opposite side of the blade. Thoroughly brush off the dust and smoothen the burrs after cleaning. Now you can move forward with the board for the table.

2. Board To Attach The Circular Saw

You do not need a brand-new and high-quality board for this. If you have any leftover thick board you can make it work. Any sort of board will do honestly. You can opt for a quadrant piece of MDF or an old, laminated particle board.

Make sure the board has a thickness of around 1.8 to 2 inches. For reference, an old board for a cupboard or a kitchen closet would suffice. If the board is straight and the edges are perfectly square, you can nominate the board for this job.

3. Placement Of The Circular Saw

You have full liberty in the position you want your circular saw to be. I prefer it on the 30 cm front to the saw, but you place it as per your comfort level. Only make sure that the circular saw is parallel to the board.

After placing, mark the five holes you made earlier on the circular saw on the table so that you can identify the position correctly. Now, drill holes in those marks. The holes have to accommodate the head of the bolts so that they can sit flat.

Use 16-millimeter wood screws that have a flat head. These screws work neatly on a flat surface as it gives more holding surface and sits precisely on the flat circular saw base. Screw the perfectly aligned to the circular saw and tighten them securely on board.

4. Cut A Line With A Circular Saw

Once the circular saw is secured, use that blade to cut a deep cut on the board. You don’t have to go overboard with this. Just carefully dig the board as far as it goes. Once the blade is on the other side of that board, check whether the circular saw is perpendicular to the surface and to the front edge.

5. Fixing Structure For Table Saw Legs

Gather two beams for the table and mark them according to the board with a circular saw. make sure the beams are tall enough to have an air gap from the base and circular saw. Drill the necessary holes to fixate the beams to the boards and screw them tightly on both sides.

Now rotate the beam with the board and attach the legs on both sides. You can use the same board you used for the tabletop. Drill holes in the legs so that they can be attached to the beams. At least 10-12 screw holes should be inserted on one side for a sturdy structure.

Once the leg is stable, insert another board in the under-middle of the leg so that it can support the whole base. Vertically drill some holes and attach that board on both sides. Once the leg portion is complete, make room for placing the table in your workshop.

6. Zip Tie To The Pressed Trigger

As the whole machine is on the downside, it is hard to see the machine from the top. To avoid any casualties, you should tie the trigger to start the tool so that you don’t turn the machine accidentally with your knees.

7. Hang The Power Line

Make two holes in one side of the leg to zip a power strip. You can use a power strip with an on/off button for easier execution. You can also manually turn the tool on and off without pressing on the circular saw. secure the power line with zip ties or rope.

8. Make Side Fence

To keep the cutline steady and the material straight, make a side fence on one side of the table. You don’t have to build a permanent fence for this. You can make a temporary fence with a square beam and two clamps. And boom! You have a table saw without spending any bucks on a table saw.

Precautions To Mount The Circular Saw As A Table Saw

Mounting a circular saw to be used as a table saw saves you lots of trouble and money. However, as the circular saw is a very heavily powered tool, you should maintain caution and care before you jump on the project of table mounting.

Protect The Fingers

No matter what method you opt for, always take the utmost precautions for the safe and sound use of the circular saw mounted on the table. The first a foremost safety tip is to keep the fingers away from the blade.

On a table saw, a lot of safety tools are surrounded by the blade. But in this improvised saw, the blade is wide and open to attack. So, use a feather board or push stick to induce the material through the blade. You should also wear eye and sound protection kits.

Go Through The Manual

It is highly recommended that you thoroughly read the manual of the circular saw and give a deep focus on the weight of the circular saw. If the circular saw can’t be matched with the board you are attaching to, you are putting yourself and the saw at risk of damage. Some manuals also prescribe whether the particular model is safe for table mounting or not.

Some Tips To Remember

Always use flat surface screws to drill and screw the parts of the saw. Make sure that the holes that you drill have no gaps or lacunas.
Never leave the power line on when the saw is not in use. Remember to detach the adaptor after you finish your work.
As the sawdust would be collected from underneath, always keep the bottom area clean and dust free after a cutting session. The dust gathered might penetrate through the saw and damage the tool.

Final Words

A circular saw is a versatile tool, and you can convert it into a table saw with only some boards and a drill machine. Now, you don’t have to spend bucks on a brand-new table saw. Remember to follow the guidelines for the precise execution of the circular saw as a table saw.